Compare Prices

Pwm Motor Driver


>
Pwm Motor Driver - HiLetgo PCA9685 16 Channel 12-Bit PWM Servo Motor Driver IIC Module For Arduino Robot
HiLetgo PCA9685 16 Channel 12-Bit PWM Servo Motor Driver IIC Module For Arduino

Pwm Motor Driver

Technical Parameters: Voltage: DC5-10V power supply Communication Interface: IIC 16-way steering gear control Size:25*61mm Product features: The PCA9685 chip is wrapped in the center of the board Power input terminal Green power indicator In the 4 groups of 3-pin connector to facilitate the insertion of 16 servo motor (servo motor plug slightly wider than 0.1 ") The polarity of the reverse polarity is input on the terminal block Cascade design: V + line to place a large capacitor, the maximum external input voltage depends on the 10V 1000uf capacitor All PWM output lines have a 220 ohm series resistor protection and can easily drive LED

  • Color: Blue
  • Brand: HiLetgo
  • ASIN: B01D1D0CX2
Pwm Motor Driver - DROK 200203 DC 5-36V 400W Dual Large Power MOS Transistor Driving Module, FET Trigger Switch Board, 0-20KHz PWM Electronic Switch Control, DC Motor Speed Controller
DROK 200203 DC 5-36V 400W Dual Large Power MOS Transistor Driving Module, FET Trigger Switch Board, 0-20KHz PWM Electronic Switch Control, DC Motor Speed

Pwm Motor Driver

Technical Parameters: Operating voltage: DC 5V - 36V; Trigger source: digital high-low (DC3.3V-20V) (can be connected IO port of microcontroller, PLC interfaces, DC power, etc.. The module can access PWM signal, which can perfectly supported the frequency of 0-20KHZ.) Output voltage: DC 5V - 36V, Output current: 15A (continuous current, at room temperature. Enhance heat dissipation, the max. current can up to 30A) Output power: 400W Operating temperature: -40-85 ℃ Dimension: 34 × 17 × 12mm. Application: High Power equipment, motors, light bulbs, LED lights, DC motors, micro-pumps, solenoid valve; can input PWM to control motor speed or lamp brightness. Package Includes: 1× MOS Driving Module

  • Brand: DROK
  • ASIN: B01J78FX9S
Pwm Motor Driver - Motor Speed Controller, DROK Brush Motor Driver Controls Module DC 9V-60V 12V 24V 36V 48V 60V Motor Pulse Width Modulator Regulator 20A 1200W PWM Monitor Dimmer Governor with Switch & Knob
Motor Speed Controller, DROK Brush Motor Driver Controls Module DC 9V-60V 12V 24V 36V 48V 60V Motor Pulse Width Modulator Regulator 20A 1200W PWM Monitor Dimmer Governor with Switch &

Pwm Motor Driver

DROK Motor Speed Controller Technical Parameters: Input voltage range: DC 9-60V Output voltage: linear under load Output current: 0-20A Continuous power: 1200W Speed control way: potentiometer (linear) Speed regulation range: 0-100% Control frequency: 25KHz Clockwise/anticlockwise rotation: support Fit motors: DC brush Dimension: 92x52x36mm The diameter of the potentiometer installed hole: 7mm Wiring Connection: Thick red wire: power supply + Thick black wire: power supply - Thick blue wire: motor + Thick green wire: motor - Package Including: 1x DC Motor Controller

  • Brand: DROK
  • ASIN: B07F7R76B8
Pwm Motor Driver - Onyehn 16 Channel PWM Servo Motor Driver PCA9685 IIC Module 12-Bit for Arduino Robot or Raspberry pi(3pcs of Pack)
Onyehn 16 Channel PWM Servo Motor Driver PCA9685 IIC Module 12-Bit for Arduino Robot or Raspberry pi(3pcs of

Pwm Motor Driver

It's an I2C-controlled PWM driver with a built in clock. That means that, unlike the TLC5940 family, you do not need to continuously send it signal tying up your microcontroller, its completely free running! Output enable pin to quickly disable all the outputs. Terminal block for power input (or you can use the 0.1" breakouts on the side). Reverse polarity protection on the terminal block input. Green power-good LED. 3 pin connectors in groups of 4 so you can plug in 16 servos at once (Servo plugs are slightly wider than 0.1" so you can only stack 4 next to each other on 0.1" header. "Chain-able" design. A spot to place a big capacitor on the V+ line. 330 ohm series resistors on all the output lines to protect them, and to make driving LEDs trivial. Solder jumpers for the 6 address select pins. Package Include: 3 * PWM Servo Motor Driver

  • Brand: Onyehn
  • ASIN: B07GJCPWW2
Pwm Motor Driver - HiLetgo 2pcs PCA9685 16 Channel 12-Bit PWM Servo Motor Driver IIC Module for Arduino Robot
HiLetgo 2pcs PCA9685 16 Channel 12-Bit PWM Servo Motor Driver IIC Module for Arduino

Pwm Motor Driver

Technical Parameters: Voltage: DC5-10V power supply Communication Interface: IIC 16-way steering gear control Size:25*61mm Product features: The PCA9685 chip is wrapped in the center of the board Power input terminal Green power indicator In the 4 groups of 3-pin connector to facilitate the insertion of 16 servo motor (servo motor plug slightly wider than 0.1 ") The polarity of the reverse polarity is input on the terminal block Cascade design: V + line to place a large capacitor, the maximum external input voltage depends on the 10V 1000uf capacitor All PWM output lines have a 220 ohm series resistor protection and can easily drive LED

  • Color: Blue
  • Brand: HiLetgo
  • ASIN: B07BRS249H
Pwm Motor Driver - DC Motor Driver, DROK L298 Dual H Bridge Motor Speed Controller DC 6.5V-27V 7A PWM Motor Regulator Board 12V 24V Electric Motor Control Module Industrial 160W with Optocoupler Isolation
DC Motor Driver, DROK L298 Dual H Bridge Motor Speed Controller DC 6.5V-27V 7A PWM Motor Regulator Board 12V 24V Electric Motor Control Module Industrial 160W with Optocoupler

Pwm Motor Driver

Parameters: 1. Power supply voltage 6.5V-27V, the power cannot be reversed or over 27V, or may burn the module, it is recommended connecting in series 15A fuse in the power input. 2. Dual motor interface, each rated output current 7A, peak current 50A, the motor interface cannot short-circuit, it is recommended connecting in series 15A fuse. 3. The enable signal and forward and reverse control signal control voltage 3-6.5V. 4. Enable signal terminal (ENA) input PWM can regulate speed, PWM frequency range 0-10KHZ, PWM minimum pulse width 10us. 5. Product dimension: 55x55x16mm  6. Installation hole diameter: 3mm, noted to prevent short circuit when install the reverse side, you can add insulation pad or copper column to raise the circuit board Parameters matched: Motors with rated voltage 24V, identification of rated power 115W or below, and motors with identification of rated current 7A can full work for a long time. Note:  1. Drive power cannot be reversed, it is recommended connecting in series 15A fuse in the power interface, the voltage should be between 6.5 - 27V. If over voltage, it may burn the drive module if power on. 2. It is recommended that the rated output current of the power supply be more than 2 times, in case the power supply voltage cannot reach the required ...

  • Brand: DROK
  • ASIN: B06XGD5SCB
Pwm Motor Driver - WINGONEER Dual Channel L298N PWM Speed DC Motor Driver Board Dual H-Bridge Stepper Motor Module - 5pcs
WINGONEER Dual Channel L298N PWM Speed DC Motor Driver Board Dual H-Bridge Stepper Motor Module -

Pwm Motor Driver

Description1. Use of imported original chip, built-in low on-resistance MOS switch, minimal heat, no heat sink, small size, low power consumption, is ideal for battery powered.(L298N internal transistor switch, low efficiency, high fever, need to add heat sink, bulky, L298N very easy to burn)2. Dual 1.5A * 2, the peak current to be 2.5A, built-in thermal protection circuit, do not be afraid motor stall burned, automatic recovery after the temperature dropped.3. Small size, light weight, 0 standby current, is the ideal choice for your car model.Product parameters:1. Dual H-bridge motor driver, can drive two DC motors or a 4-wire two-phase stepper motor;2. The module supply voltage 2V-10V;3. Signal input voltage 1.8-7V;4. Single Operating current 1.5A, peak current up to 2.5A, low standby current (less than 0.1uA);5. Built-in common conduction circuit, when the input pin is left floating, the motor does not malfunction;6. Built-in thermal protection circuit with hysteresis effects (TSD), without worrying about motor stall;7. Product Size: 24.7 * 21 * 5mm (length, width, height), ultra-small size;8. The mounting hole diameter: 2 mm.9. Weight: 5gPrecautions:1. Power positive and negative reversed will certainly cause damage to the circuit.2. Output is shorted to ground or output shor...

  • Brand: WINGONEER
  • ASIN: B07FDSHVCS
  • UPC: 723466655835
Pwm Motor Driver - uniquegoods 1.8v 3v 5v 6v 7.2v 12v 2A 30W DC Motor Speed Controller (PWM) 1803BK Adjustable Driver Switch
uniquegoods 1.8v 3v 5v 6v 7.2v 12v 2A 30W DC Motor Speed Controller (PWM) 1803BK Adjustable Driver

Pwm Motor Driver

Features: 1803BK DC Motor Speed Regulator controls the speed of a DC motor by adjusting Pulse-Width-Modulated (PWM).  The input power range is DC 1.8-15V . Use a 2A resettable fuse to protect the controller. Potentiometer with switch function. Operating instruction:  Before you attempting to wire the controller, make sure power is off. WARNING: TO CHANGE MOTOR DIRECTION, INTERCHANGE THE POSITIVE AND NEGATIVE WIRES OF MOTOR. 1. Connect wires refer to the "wiring diagram" (NO.5 picture). 2. Turn on the power, and adjust the potentiometer. 3. The LED indicates the power up and the speed of motor. Package Including: 1 x DC Motor Speed Controller

  • Brand: uniquegoods
  • ASIN: B00QGMESHM
  • UPC: 605145000450
Pwm Motor Driver - MakerFocus PWM Servo Motor Driver IIC Module 16 Channel PWM Outputs 12 Bit Resolution I2C Interface Compatible Raspberry Pi Zero/Zero W/Zero WH/2B/3B/3B Robot
MakerFocus PWM Servo Motor Driver IIC Module 16 Channel PWM Outputs 12 Bit Resolution I2C Interface Compatible Raspberry Pi Zero/Zero W/Zero WH/2B/3B/3B

Pwm Motor Driver

Overview:Needless to say, the Raspberry Pi is powerful enough in most cases, yet it's not that good at providing precise PWM output. You may have tried to control a robotic arm or a hexapod walker by using the Pi, but finally get frustrated due to the limited number of PWM outputs and the jittering servo. Now you get a new option to bring your ideas to life, we prepare this useful Servo Driver Board for you.Features:Raspberry Pi connectivity, compatible with Raspberry Pi Zero/Zero W/Zero WH/2B/3B/3B+I2C controlled, using only 2 pinsUp to 16-Channel servo/PWM outputs, 12-bit resolution for each channel (4096 scales)Integrates 5V regulator, up to 3A output current, can be powered from battery through VIN terminalStandard servo interface, supports common used servo such as SG90, MG90S, MG996R, etc.Reserved I2C control pins, allows to work with other control boardsSpecifications:Power supply: 5V (Pi connector) OR 6V~12V (VIN terminal)Servo voltage: 5VLogic voltage: 3.3VDriver: PCA9685Control interface: I2CDimension: 65mm x 30mmMounting hole size: 3.0mmPackage Including:1 * PWM Servo Motor Driver IIC Module1 * RPi screws(2 pack)

  • Color: PWM Servo Motor Driver
  • Brand: MakerFocus
  • ASIN: B07H9ZTWNC
  • UPC: 673400140173

Pwm Motor Driver Z266 Search Results

Looking for more Pwm Motor Driver similar ideas? Try to explore these searches: Clad Pcgs Proof, Wax Resin Print Ribbon, and French Roast Blended Coffee.

Related Pwm Motor Driver Video Reviews

Look at latest related video about Pwm Motor Driver.

Shopwizion.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com. Amazon and the Amazon logo are trademarks of Amazon.com, Inc. or one of its affiliates.